FAQ

ATAS offers a wide style of metal roof systems to complement almost any architectural style desired.

Yes.  There are various custom colors and color match service is available for a reasonable cost.

ATAS International, Inc. manufacturers metal roof systems that are considered structural and non-structural in nature. Actual panel profile and gauge of the material will determine if the panel has structural capability to span over open framing.  Consult individual product data sheets to see if the profile desired is considered a structural panel system.

Most metal panel systems can support the load of an individual walking on them.  As with any roof system care must be taken  to not cause damage to the roof due to abrasion or collapsing of raised portion of the panel.  Appropriate OSHA approved safety procedures should also be followed.

ATAS International Inc. is a manufacturer of roof, wall, ceiling panels and components only.  Installation of these materials is performed by installers and contractors who are familiar with the proper detailing of these systems.  It is recommended that you consult with your contractor to ensure his familiarity with installation of metal systems.

ATAS International Inc. has a nationwide network of Technical Advisors available to answer any questions or concerns about metal roof materials.

Yes.  ATAS has a fully staffed engineering department that can assist with your project.

Metal roof systems can offer compliance with many of today’s new requirements for “sustainable building construction.”  ENERGY STAR®, CRRC® and LEED® ratings can be accommodated using metal roof products supplied by ATAS.  We can offer assistance in proper panel and coating selection for your individual building requirements.

Lightning is attracted to the highest point, not necessarily metal.  A metal roof has no greater chance of being hit by lightning than any other type of roof.  However, if your roof would be struck by lightning, a metal roof can help prevent your home from catching on fire because it can dissipate the electrical charge.  More importantly, it is noncombustible.

Touch up paint is available from ATAS to repair any slight surface scratched on the panel.  A specialist in the recoating of metal products should be consulted if a large area of the roof is required to be repaired.

Metal roof systems when installed properly, offer a high degree of resistance to the forces of nature.  These include resistance to wind uplift, fire and impact.  Metal roof systems have been installed throughout the world in some of the harshest climate conditions.

Span capability of a panel is dependent upon profile, gauge and width of the panel itself.  Consult individual load tables and test results to see if the panel meets the actual performance requirements for your project.

Metal roof systems in most cases weigh between 1 to 3 pounds per square foot.  The actual weight is dependent upon metal gauge and profile of the panel.  Metal roof systems are considered a lightweight roof covering compared to their counterparts.  An example of this would be our ScanRoof and Techo Tile panels that are tile facsimiles of traditional clay or concrete tiles.  These systems weigh no more than 1.5 pounds per square foot versus their traditional counterparts that weigh often in excess of 9 pounds per square foot.

A metal roof offers a building owner a long life system that requires a minimal amount of maintenance.  Over the life of a roof, metal is probably the most economical system available.  Traditional roofing materials have a limited life expectancy before one is faced with the expense as well as the disruption of daily activities associated with replacement.  Traditional roof systems have a high degree of maintenance required to perform as expected over the anticipated life.  With a high quality metal roof system, maintenance is minor, therefore maintenance costs are almost non-existent.

Yes, metal is a fire resistant material.  For more information contact our offices.

Metal is a preferred roofing material in hail prone areas.  Hail causes extensive damage to roofs because it can break, split and cause tear-off of traditional roofing materials.  However, hail will not penetrate a metal roof.  In the severest case, the various styles and finishes available in metal roofing can help camouflage potential cosmetic damage.

ATAS International Inc. manufactures a wide variety of panel systems to meet a variety of slope requirements.  Information regarding minimum slope requirements can be found on the specific technical Data Sheet for each product.  Typically, metal panel systems are considered to be “hydrostatic” in nature and these systems can be applied to slopes of ½:12 (consistent with guidelines published by NRCA) or “hydrokinetic” in nature and require slopes of 2:12 and above.  Actual minimum slopes may be dependent upon roof geometry, substrate, and physical location of the project.

Snow retention systems are often incorporated into metal roof system.  These systems are used to retain snow on the roof for protection as well as water management.  The actual style of snow guards to be used may be dependent upon the panel style as well as the aesthetic nature of the snow guard itself.  Consult with your ATAS representative or independent snow guard manufacturer to select the appropriate snow guard for your roof.

ATAS offers panel systems with a premium base metal and a premium paint finish that is designed to resist fading and chalking. All products carry a standard 20-year material and finish warranty are guaranteed against manufacturing defects. A 25 and 30 year finish warranties are available upon special request and may be subject to limitations. Special weather tight roof warranties are also available on specific panel styles. All weather tightness warranties are subject to a fee and projects are required to be inspected to ensure quality installation methods are being performed. For more information regarding these warranties, consult your ATAS representative or visit our Warranty Programs page.

Installation guides are found on individual product pages when available.

ATAS International Inc. utilizes high quality premium base metals in the manufacturing of its products.  All panels are produced from a minimum of G90 galvanized steel.  Galvanized steel describes a steel product with a metallic coating that inhibits corrosion of the steel itself.  These products have a proven history in field performance.  In addition, ATAS International Inc. produces panels in aluminum, copper, zinc as well as stainless steel for areas in which corrosion is of extreme concern.  Actual product performance is dependent upon the environmental conditions they may be subject to.  The premium paint coatings that are applied to steel and aluminum are designed to resist chalking and fading.  In addition, the most sophisticated pretreatment systems are utilized in the paint application process that further enhance corrosion protection of the base metals.

ATAS International, Inc. sells through a nationwide network of Dealers and Distributors.  Contact your local distributor to inquire about ATAS products and services.